Little Giant # 584698 TE-5-MD-HC Magnetic Drive Centrifugal Pump
Little Giant # 584698
Little Giant catalog # 584698, TE-5-MD-HC Magnetic Drive Centrifugal Pump, replacement Pump End only, no motor. Inlet Port is 1 inch FNPT, Discharge Port is 1/2 inch MNPT.
Price : $ 297.00
Product Information :
Specsheet PDF (view)
The Little Giant 584698 is a TE-5-MD-HC Magnetic Drive Centrifugal Pump, replacement Pump End only, no motor, with a 1 inch FNPT inlet port by 1/2 inch MNPT outlet port, replacement pump end only without a Motor. The Little Giant MD-HC series features leakproof, seal-less magnetic drives and are designed for in-line, non-submersible use. Volute, magnet housing and impeller are glass-filled Ryton for excellent chemical resistance. Ceramic shaft and thrust washers are 99.5% pure alumina for excellent wear and trouble-free service. Pumping heads are easily rotated, cleaned or serviced with no special tools required. Spindle shaft is supported at both ends to prevent impeller damage during start-up and stop of pump. The pump's volute and housing are made from glass-filled Ryton; its impeller, glass-filled Ryton with carbon bushing; its shaft and thrust washers, ceramic; and its O-Ring, Viton. This pump uses ball bearings, a 6 foot power cord with a 3-prong plug, and a thermally protected, totally enclosed, fan-cooled, permanent split capacitor motor. It can pump liquids with a specific gravity up to 1.1, and a run-dry capacity of up to 8 hours. It can pump fluids with a temperature of up to 200 F, and can operate in a maximum ambient air temperature of 77 F
WEIGHT : The Little Giant 584698 weighs 2.17 Lbs.
Features :
Applications
There are many applications that the Little Giant 584698 are used in. Typical applications for this pump include Circulation of highly corrosive acids, alkalis, solvents, brine, plating solutions, sterile solutions, and other highly corrosive chemicals and solutions that are compatible with the pump's material of construction.
This Little Giant pump is delivered to you completely preassembled and pretested from the factory. It is ready for immediate use. The pump may be installed in any position. It may be mounted vertically with the pump head down. Proper plumbing connections should be made. See specification table to determine what size intake and discharge The pump has. Use a thread sealer on all pipe connections and hand tighten only. NOTE On HC models a roll of PTFE pipe seal tape is supplied. Do not use a wrench to tighten the HC model connections. Excessive force may damage the plastic part. Make sure the wing nuts are tight before operating the pump. Motor nameplates list all electrical data and wiring schematic. Make sure the pump is connected to proper voltage before operating. When wiring pumps with no plug, the green or green/yellow wire is the ground. The other two wires are line live. Do not allow the SC models to run dry without fluid. However, because the HC models utilize a carbon bushing in the impeller they may be allowed to run dry for periods up to eight hours at a 1 5mdsc 5mdhc te5mdsc te5mdhc Franklin Electric Co., Inc. Oklahoma City, OK 73127 www.LittleGiantPump.com CustomerServicelgpc.com time. These pumps are not submersible. Operate the pumps only in the inline mode. Do not put the units in liquid. Pump should be installed in a dry area and protected from splash. These pumps are not self priming models. They must be installed so that the pump head volute is flooded at the time the pump is to be started. That is, the inlet of the pump must be below the level of the surface of the liquid being pumped. See Figure 1. Do not restrict the intake side of the pump. Connections on the intake side should not be of smaller inside diameter pipe or tubing or hose than the inside diameter of the intake thread designation. If reduced flow is required restrict the discharge side. Installing a valve or other type of restriction device on the discharge side is the proper method for reducing flow from the pump. When using a valve the pump can be throttled to provide various flow rates and pressures without harming the motor or the pump parts. The pump should not be installed in a manner that will subject it to splashing or spraying